Referring to the exhibit,

#show lag

Total number of LAGs: 1

Total number of deployed LAGs: 0

Total number of trunks created:0 (128 available)

LACP System Priority / ID: 1 / 0024.3891.4f00

LACP Long timeout: 90, default: 90

LACP Short timeout: 3, default: 3

=== LAG "30Gig_Trunk" ID 1 (dynamic Not Deployed) ===

LAG Configuration:

Ports: e 1/3 e 1/5 e 1/7

Port Count: 3

Primary Port: 1/3

Trunk Type: hash-based

LACP Key: 100

Which command must be entered to make the LAG function on a

Brocade NetIron MLXe?

You have been informed a group of remote employees are unable to authenticate with the RADIUS server. From the Brocade FCX router, you enable the debug dot1x events command.

Which three events will be viewed? (Choose three.)

A customer wants to use a cable that provides maximum EMI protection. Which type of cable should be used?

Which three statements are true about RIPv2 and OSPF? (Choose three.)

Which IPv6 address is correctly formatted?

Which technology allows a service provider the ability to connect customer sites with duplicate tagged VLAN configurations across the same circuit as shown in the exhibit?

When configuring an IP static route in a Brocade router, which three parameters are required?

(Choose three.)

Brocade support has requested that you gather supportsave data for troubleshooting an issue on a Brocade FastIron ICX. Which service is required to transfer the files?

Given the command output shown below:

de(config)#mirror-port ethernet 1/2/4

Brocade(config)#interface ethernet 1/2/11

Brocade(config-if-e100-11)#monitor ethernet 1/2/4 both

What do the Brocade commands accomplish?

Referring to the exhibit, port eth 1 on Switch-A is connected to port eth 1 on Switch-B.

Switch-A#show int eth 1

GigabitEthernet1 is up, line protocol is up

Hardware is GigabitEthernet, address is 748e.f821.3ad3 (bia 748e.f821.3aeb)

Configured speed auto, actual 1Gbit, configured duplex fdx, actual fdx

Configured mdi mode AUTO, actual MDI

Member of L2 VLAN ID 1, port is untagged, port state is FORWARDING

BPDU guard is Disabled, ROOT protect is Disabled

STP configured to ON, priority is level0

Flow Control is config enabled, oper enabled, negotiation disabled

mirror disabled, monitor disabled

Not member of any active trunks

Internet address is 192.168.5.2/24, IP MTU 9198 bytes, encapsulation ethernet

<

>

Switch-B#show int eth 1

GigabitEthernet1 is up, line protocol is up

Hardware is GigabitEthernet, address is 748e.f821.443a (bia 748e.f821.4453)

Configured speed auto, actual 1Gbit, configured duplex fdx, actual fdx

Configured mdi mode AUTO, actual MDI

Member of L2 VLAN ID 1, port is untagged, port state is FORWARDING

BPDU guard is Enabled, ROOT protect is Disabled

STP configured to ON, priority is level0

Flow Control is config enabled, oper enabled, negotiation disabled

mirror disabled, monitor disabled

Not member of any active trunks

Internet address is 192.168.5.3/24, IP MTU 1000 bytes, encapsulation ethernet

<

>

You notice high packet loss between the two devices communicating over this link.

What is causing high packet loss over this link?

What are two functions of an OSPF Autonomous System Boundary Router (ASBR)? (Choose two.)

You want the links between two switches to forward traffic for more than one VLAN.

What should you use to configure the inter-connected ports?

In the exhibit, the network is running Spanning Tree 802.ID. Which port will be placed in a blocked state?